Fit Check on every partFree shipping over $4930-day returns
Help: contact us
HVAC FitterTHE PART THAT FITS
PART NUMBER · CARRIER

Carrier EF32CW151 Gas Valve

Out of stock

The Carrier EF32CW151 is a gas valve designed for heating systems. It regulates the flow of fuel to the furnace burners when heat is needed.

This part is out of stock right now, so it cannot be added to the cart.

One email when it is back in stock. Nothing else. Privacy policy

When the thermostat calls for heat, the control board signals the gas valve to open. The valve delivers the right amount of gas to the burners so they can ignite safely.

Safety first. If you smell gas, do not touch any switch or use a phone inside. Leave the house right away and call your gas company from outside. Turn off electrical power at the breaker and test for power before touching any wires. Gas valve work means opening gas lines and setting gas pressure. A licensed pro should do the installation.

Specifications

FROM THE PART LISTINGS
  • Part number: EF32CW151
  • Brand: Carrier
  • Part type: Gas valve
  • Dimensions: 6.9 × 6.9 × 3.4 in
  • Gas type: Natural Gas
  • Pressure: 3.5" wc
  • Voltage: 24 VAC
  • Wiring: 1/2″
MATCH THESE NUMBERS ON YOUR OLD GAS VALVE
  • Gas type: natural gas or propane, as listed
  • Ignition: same type as your furnace
  • Pipe size and BTU: same pipe size, rated for your furnace

From the maker's and parts sellers' listings for this number. Compare them with the label on your old part.

How the Gas Valve Works

A gas valve acts as an automatic safety switch and regulator for your furnace. It stays closed until the system completes several safety checks, including proof of draft and ignition.

Once the system is ready, the valve solenoid opens using a low-voltage signal. This allows fuel to flow directly into the burner assembly. If safety switches open or power drops, the valve closes tightly to stop the flow of gas.

Understanding the EF32CW151 Specifications

Every gas valve has specific ratings to ensure safe operation. The specs on the EF32CW151 label describe its fuel type, power needs, and physical size.

  • Gas type: Natural Gas
  • Pressure: 3.5" wc
  • Voltage: 24 VAC
  • Wiring: 1/2″
  • Dimensions: 6.9 × 6.9 × 3.4 in

Confirming a Match

Replacing a gas valve requires an exact match for safety. Installing a valve with the wrong fuel type or pressure rating creates serious hazards.

Always check that the replacement matches the gas type of your system, whether natural gas or propane. It must also match the pipe size, rated BTU for your furnace, and the ignition type used by your equipment.

Signs of Failure and Safe Replacement

A furnace may fail to light if the gas valve solenoid fails or sticks shut. The igniter might glow, but no flame appears because fuel is blocked from reaching the burners.

Replacing this component involves disconnecting fuel lines, reconnecting low-voltage wiring, and setting the manifold gas pressure. Take a photo of every wire before disconnecting anything. Move wires one at a time to the same spots on the new part.

Read your old part

  1. Shut off power and access the furnace burner compartment.
  2. Locate the metal rating plate or sticker on the body of your existing gas valve.
  3. Read the part number stamped on the valve and look for EF32CW151.
  4. Check that the gas type says Natural Gas and the pressure rating shows 3.5" wc.
  5. Verify that the voltage requirement shows 24 VAC before proceeding.

When to call a pro

Gas valve work means opening gas lines and setting gas pressure. We strongly suggest a licensed tech does the install. Hire a licensed HVAC technician for any step you are not sure you can do safely.

Questions

What fuel type does the EF32CW151 gas valve use?

The Carrier EF32CW151 is rated for Natural Gas. Do not use it with propane unless properly converted and approved for your equipment.

What voltage operates this valve?

This valve operates on 24 VAC. Most home thermostats and furnace control boards provide this 24 V control signal from a transformer.

What should I do if I smell gas around the furnace?

Leave the house immediately. Do not touch any electrical switches or use phones inside. Call your gas company from outside once you are safe.

Can I install a gas valve myself?

Gas valve work means opening gas lines and setting gas pressure. We strongly suggest a licensed HVAC pro does the installation to ensure it is sealed and calibrated correctly.

Related part numbers

Browse: Carrier part numbers · Furnace gas valves by part number

All part numbers · Part number replacements · Shop gas valves · Repair guides

Brand names and part numbers identify the part and show fit. HVAC Fitter is not affiliated with, authorized by, or endorsed by any equipment maker. If you are not sure a repair is safe for you, call a licensed HVAC technician.